Added a few command descriptions.

[ArmanHayots]

No description provided.

[yukulele]

Full list:

{
  "gcode.definitions": {
    "G0": "Rapid, linear interpolation",
    "G1": "Feed, linear interpolation",
    "G2": "Feed, circular interpolation, clockwise",
    "G3": "Feed, circular interpolation, counter-clockwise",
    "G4": "DWELL: Pause the planner",
    "G5": "BÉZIER CUBIC SPLINE: Cubic B-spline with XYZE destination and IJPQ offsets",
    "G10": "RETRACT: Retract the filament",
    "G11": "RECOVER: Recover the filament with firmware-based retract.",
    "G12": "CLEAN THE NOZZLE: Perform the nozzle cleaning procedure.",
    "G17": "CNC WORKSPACE PLANES: Select CNC workspace plane",
    "G18": "CNC WORKSPACE PLANES: Select CNC workspace plane",
    "G19": "CNC WORKSPACE PLANES: Select CNC workspace plane",
    "G20": "INCH UNITS: Set Units to Inches.",
    "G21": "MILLIMETER UNITS: Set Units to Millimeters.",
    "G26": "MESH VALIDATION PATTERN: Test the mesh and adjust.",
    "G27": "PARK TOOLHEAD: Park the current toolhead",
    "G28": "AUTO HOME: Auto home one or more axes.",
    "G29": "BED LEVELING: Probe the bed and enable leveling compensation",
    "G30": "SINGLE Z-PROBE: Probe bed at current XY location",
    "G31": "DOCK SLED: Dock the Z probe sled.",
    "G32": "UNDOCK SLED: Undock the Z probe sled.",
    "G33": "DELTA AUTO CALIBRATION: Calibrate various Delta parameters",
    "G34": "Z STEPPERS AUTO-ALIGNMENT: Align multiple Z steppers using a bed probe",
    "G35": "TRAMMING ASSISTANT: Run a procedure to tram the bed",
    "G38.2": "PROBE TARGET: Probe towards a workpiece and stop on contact.",
    "G38.3": "PROBE TARGET: Probe towards a workpiece and stop on contact.",
    "G42": "MOVE TO MESH COORDINATE: Move to a specific point in the leveling mesh",
    "G53": "MOVE IN MACHINE COORDINATES: Apply native workspace to the current move.",
    "G54": "WORKSPACE COORDINATE SYSTEM: Select a workspace coordinate system",
    "G55": "WORKSPACE COORDINATE SYSTEM: Select a workspace coordinate system",
    "G56": "WORKSPACE COORDINATE SYSTEM: Select a workspace coordinate system",
    "G57": "WORKSPACE COORDINATE SYSTEM: Select a workspace coordinate system",
    "G58": "WORKSPACE COORDINATE SYSTEM: Select a workspace coordinate system",
    "G59": "WORKSPACE COORDINATE SYSTEM: Select a workspace coordinate system",
    "G59.1": "WORKSPACE COORDINATE SYSTEM: Select a workspace coordinate system",
    "G59.2": "WORKSPACE COORDINATE SYSTEM: Select a workspace coordinate system",
    "G59.3": "WORKSPACE COORDINATE SYSTEM: Select a workspace coordinate system",
    "G60": "SAVE CURRENT POSITION: Save current position to specified slot",
    "G61": "RETURN TO SAVED POSITION: Return to saved position of specified slot",
    "G76": "PROBE TEMPERATURE CALIBRATION: Calibrate probe temperature compensation",
    "G80": "CANCEL CURRENT MOTION MODE: Cancel the current motion mode",
    "G90": "ABSOLUTE POSITIONING: Set the interpreter to absolute positions",
    "G91": "RELATIVE POSITIONING: Set the interpreter to relative positions",
    "G92": "SET POSITION: Set the current position of one or more axes.",
    "G425": "BACKLASH CALIBRATION: Use a conductive object to calibrate XYZ backlash",
    "M0": "UNCONDITIONAL STOP: Stop and wait for user.",
    "M1": "UNCONDITIONAL STOP: Stop and wait for user.",
    "M3": "SPINDLE CW / LASER ON: Set the spindle CW speed or laser power",
    "M4": "SPINDLE CCW / LASER ON: Set the spindle CCW speed or laser power",
    "M5": "SPINDLE / LASER OFF: Turn off spindle or laser",
    "M7": "COOLANT CONTROLS: Turn mist or flood coolant on and off",
    "M8": "COOLANT CONTROLS: Turn mist or flood coolant on and off",
    "M9": "COOLANT CONTROLS: Turn mist or flood coolant on and off",
    "M16": "EXPECTED PRINTER CHECK: Prevent G-code usage on the wrong machine",
    "M17": "ENABLE STEPPERS: Enable steppers",
    "M18": "DISABLE STEPPERS: Disable steppers (same as M84).",
    "M84": "DISABLE STEPPERS: Disable steppers (same as M16).",
    "M20": "LIST SD CARD: List the contents of the SD Card.",
    "M21": "INIT SD CARD: Attempt to detect an SD card in the slot.",
    "M22": "RELEASE SD CARD: Simulate ejection of the SD card",
    "M23": "SELECT SD FILE: Select an SD file to be executed",
    "M24": "START OR RESUME SD PRINT: Start or resume a file selected with [`M23`]",
    "M25": "PAUSE SD PRINT: Pause printing from the SD card",
    "M26": "SET SD POSITION: Set the SD read position",
    "M27": "REPORT SD PRINT STATUS: Print SD progress to serial",
    "M28": "START SD WRITE: Start writing to a file on the SD card",
    "M29": "STOP SD WRITE: Stop writing the file, end logging.",
    "M30": "DELETE SD FILE: Delete a specified file from SD.",
    "M31": "PRINT TIME: Report the current print time.",
    "M32": "SELECT AND START: Begin an SD print from a file.",
    "M33": "GET LONG PATH: Convert a short pathname to a long pathname.",
    "M34": "SDCARD SORTING: Set SDCard file sorting options.",
    "M42": "SET PIN STATE: Set an analog or digital pin to a specified state.",
    "M43": "DEBUG PINS: Get information about pins.",
    "M48": "PROBE ACCURACY TEST: Measure Z Probe repeatability.",
    "M73": "SET PRINT PROGRESS: Set current print progress percentage for LCD.",
    "M75": "START PRINT JOB TIMER: Start the print job timer.",
    "M76": "PAUSE PRINT JOB: Pause the print job timer.",
    "M77": "STOP PRINT JOB TIMER: Stop the print job timer.",
    "M78": "PRINT JOB STATS: Print statistics about print jobs.",
    "M80": "POWER ON: Turn on the power supply",
    "M81": "POWER OFF: Turn off the power supply.",
    "M82": "E ABSOLUTE: Set E to absolute positioning.",
    "M83": "E RELATIVE: Set E to relative positioning.",
    "M85": "INACTIVITY SHUTDOWN: Set the inactivity timeout.",
    "M92": "SET AXIS STEPS-PER-UNIT: Set the number of steps-per-mm or steps-per-inch.",
    "M100": "FREE MEMORY: Description Here",
    "M104": "SET HOTEND TEMPERATURE: Set a new target hot end temperature.",
    "M105": "REPORT TEMPERATURES: Send a temperature report to the host.",
    "M106": "SET FAN SPEED: Turn on the fan and set its speed",
    "M107": "FAN OFF: Turn off a fan",
    "M108": "BREAK AND CONTINUE: Break out of the current waiting loop",
    "M109": "WAIT FOR HOTEND TEMPERATURE: Wait for the hot end to reach its target.",
    "M110": "SET LINE NUMBER: Set the current line number.",
    "M111": "DEBUG LEVEL: Report and optionally set the debug flags.",
    "M112": "EMERGENCY STOP: Shut everything down and halt the machine.",
    "M113": "HOST KEEPALIVE: Get or set the host keepalive interval.",
    "M114": "GET CURRENT POSITION: Report the current tool position to the host.",
    "M115": "FIRMWARE INFO: Print the firmware info and capabilities.",
    "M117": "SET LCD MESSAGE: Set the message line on the LCD.",
    "M118": "SERIAL PRINT: Send text to serial",
    "M119": "ENDSTOP STATES: Report endstop and probe states to the host.",
    "M120": "ENABLE ENDSTOPS: Enable endstops and keep them enabled when not homing.",
    "M121": "DISABLE ENDSTOPS: Disable endstops and keep them enabled when not homing.",
    "M122": "TMC DEBUGGING: Get TMC Debug Info",
    "M125": "PARK HEAD: Save current position and move to filament changeposition.",
    "M126": "BARICUDA 1 OPEN: Open the valve for Baricuda 1.",
    "M127": "BARICUDA 1 CLOSE: Close the valve for Baricuda 1.",
    "M128": "BARICUDA 2 OPEN: Open the valve for Baricuda 2.",
    "M129": "BARICUDA 2 CLOSE: Close the valve for Baricuda 2.",
    "M140": "SET BED TEMPERATURE: Set a new target bed temperature.",
    "M141": "SET CHAMBER TEMPERATURE: Set a new target chamber temperature.",
    "M145": "SET MATERIAL PRESET: Set material presets in the LCD menu.",
    "M149": "SET TEMPERATURE UNITS: Set temperature units to Celsius, Fahrenheit, or Kelvin.",
    "M150": "SET RGB(W) COLOR: Set the color of the RGB(W) LED, backlight, or LED strip.",
    "M155": "TEMPERATURE AUTO-REPORT: Auto-report temperatures to host periodically.",
    "M163": "SET MIX FACTOR: Set a single mix factor for a mixing extruder.",
    "M164": "SAVE MIX: Save the current mix as a virtual tool.",
    "M165": "SET MIX: Set all mix factors for the mixing extruder.",
    "M166": "GRADIENT MIX: Set a Gradient Mix",
    "M190": "WAIT FOR BED TEMPERATURE: Wait for the bed to reach target temperature.",
    "M191": "WAIT FOR CHAMBER TEMPERATURE: Wait for the chamber to reach target temperature.",
    "M192": "WAIT FOR PROBE TEMPERATURE: Wait for the probe temperature sensor to reach a target",
    "M200": "SET FILAMENT DIAMETER: Set the diameter for volumetric extrusion.",
    "M201": "SET PRINT MAX ACCELERATION: Set maximum acceleration for print moves one or more axes.",
    "M203": "SET MAX FEEDRATE: Set maximum feedrate for one or more axes.",
    "M204": "SET STARTING ACCELERATION: Set the starting acceleration for moves by type.",
    "M205": "SET ADVANCED SETTINGS: Set some advanced settings related to movement.",
    "M206": "SET HOME OFFSETS: Description Here",
    "M207": "SET FIRMWARE RETRACTION: Set options for firmware-based retraction.",
    "M208": "FIRMWARE RECOVER: Firmware-retraction recover settings.",
    "M209": "SET AUTO RETRACT: Enable / disable auto-retraction.",
    "M211": "SOFTWARE ENDSTOPS: Set and/or get the software endstops state",
    "M217": "FILAMENT SWAP PARAMETERS: Set length and speed for filament swapping",
    "M218": "SET HOTEND OFFSET: Set the offset of a hotend (from hotend 0).",
    "M220": "SET FEEDRATE PERCENTAGE: Set the global feedrate percentage.",
    "M221": "SET FLOW PERCENTAGE: Set the flow percentage, which applies to all E moves.",
    "M226": "WAIT FOR PIN STATE: Wait for a pin to have a given state.",
    "M240": "TRIGGER CAMERA: Trigger a camera shutter",
    "M250": "LCD CONTRAST: Set and/or get the LCD contrast.",
    "M260": "I2C SEND: Send data to the I2C bus.",
    "M261": "I2C REQUEST: Request and echo bytes from the I2C bus.",
    "M280": "SERVO POSITION: Set or get a servo position.",
    "M281": "EDIT SERVO ANGLES: Set servo deploy and/or stow angles",
    "M290": "BABYSTEP: Babystep one or more axes",
    "M300": "PLAY TONE: Play a single tone, buzz, or beep.",
    "M301": "SET HOTEND PID: Set PID values for a hotend.",
    "M302": "COLD EXTRUDE: Set minimum extrusion temperature, allow cold extrusion.",
    "M303": "PID AUTOTUNE: Auto-tune the PID system to find stable values.",
    "M304": "SET BED PID: Set PID values for the heated bed.",
    "M350": "SET MICRO-STEPPING: Set micro-stepping for drivers that support it",
    "M351": "SET MICROSTEP PINS: Directly set the micro-stepping pins",
    "M355": "CASE LIGHT CONTROL: Turn the case light on or off, set brightness",
    "M360": "SCARA THETA A: Move to Theta A",
    "M361": "SCARA THETA-B: Move to Theta-B",
    "M362": "SCARA PSI-A: Move to Psi-A",
    "M363": "SCARA PSI-B: Move to Psi-B",
    "M364": "SCARA PSI-C: Move to Psi-C",
    "M380": "ACTIVATE SOLENOID: Activate",
    "M381": "DEACTIVATE SOLENOIDS: Deactivate all extruder solenoids",
    "M400": "FINISH MOVES: Wait for all moves to finish",
    "M401": "DEPLOY PROBE: Deploy the bed probe",
    "M402": "STOW PROBE: Stow the bed probe",
    "M403": "MMU2 FILAMENT TYPE: Set filament type for Multi-Material Unit 2.0",
    "M404": "SET FILAMENT DIAMETER: Set the nominal diameter for filament width sensor auto-flow",
    "M405": "FILAMENT WIDTH SENSOR ON: Enable filament width sensor flow control",
    "M406": "FILAMENT WIDTH SENSOR OFF: Disable filament width sensor flow control",
    "M407": "FILAMENT WIDTH: Report the measured filament width",
    "M410": "QUICKSTOP: Stop all steppers instantly",
    "M412": "FILAMENT RUNOUT: Enable / disable filament runout detection",
    "M413": "POWER-LOSS RECOVERY: Enable / disable power-loss recovery",
    "M420": "BED LEVELING STATE: Get and/or set bed leveling state and parameters",
    "M421": "SET MESH VALUE: Set a single mesh Z height",
    "M422": "SET Z MOTOR XY: Set a Z motor position for G34 Auto-Alignment",
    "M425": "BACKLASH COMPENSATION: Enable and tune backlash compensation",
    "M428": "HOME OFFSETS HERE: Set home offsets based on current position",
    "M486": "CANCEL OBJECTS: Identify and cancel objects",
    "M500": "SAVE SETTINGS: Save settings to EEPROM.",
    "M501": "RESTORE SETTINGS: Restore settings from EEPROM.",
    "M502": "FACTORY RESET: Restore all settings to factory defaults.",
    "M503": "REPORT SETTINGS: Report all settings that may be saved to EEPROM.",
    "M504": "VALIDATE EEPROM CONTENTS: Validate the contents of the EEPROM.",
    "M524": "ABORT SD PRINT: Abort an SD print started with [`M24`]",
    "M540": "ENDSTOPS ABORT SD: Abort SD printing when an endstop is triggered.",
    "M569": "SET TMC STEPPING MODE: Toggle stealthChop",
    "M575": "SERIAL BAUD RATE: Change the serial baud rate",
    "M600": "FILAMENT CHANGE: Automatically change filament",
    "M603": "CONFIGURE FILAMENT CHANGE: Configure automatic filament change parameters",
    "M605": "DUAL NOZZLE MODE: Set the behavior mode for dual nozzles",
    "M665": "DELTA CONFIGURATION: Set delta geometry values",
    "M666": "SET DELTA ENDSTOP ADJUSTMENTS: Set Delta endstop adjustments",
    "M701": "LOAD FILAMENT: Load filament",
    "M702": "UNLOAD FILAMENT: Unload filament",
    "M710": "CONTROLLER FAN SETTINGS: Set or report controller fan settings",
    "M7219": "MAX7219 CONTROL: Control Max7219 Segmented LEDs",
    "M851": "XYZ PROBE OFFSET: Set the Z probe XYZ offset from nozzle",
    "M852": "BED SKEW COMPENSATION: Misalignment in the XYZ axes.",
    "M871": "PROBE TEMPERATURE CONFIG: Configure probe temperature compensation",
    "M900": "LINEAR ADVANCE FACTOR: Get and set Linear Advance K value",
    "M906": "TMC MOTOR CURRENT: Set the motor current (in milliamps)",
    "M907": "SET MOTOR CURRENT: Set motor current via digital trimpot",
    "M908": "SET TRIMPOT PINS: Set a digital trimpot directly",
    "M909": "DAC PRINT VALUES: Report DAC current values to host",
    "M910": "COMMIT DAC TO EEPROM: Commit digipot/DAC value to external EEPROM",
    "M911": "TMC OT PRE-WARN CONDITION: Driver overtemperature pre-warn condition",
    "M912": "CLEAR TMC OT PRE-WARN: Clear overtemperature pre-warn condition flag",
    "M913": "SET HYBRID THRESHOLD SPEED: TMC driver switching to spreadCycle",
    "M914": "TMC BUMP SENSITIVITY: Set sensorless homing sensitivity",
    "M915": "TMC Z AXIS CALIBRATION: Align ends of the Z axis and test torque",
    "M928": "START SD LOGGING: Log serial input to an SD file",
    "M997": "FIRMWARE UPDATE: Perform in-application firmware update",
    "M999": "STOP RESTART: Return the machine to Running state",
    "T0": "SELECT TOOL: Switch to the specified tool",
    "T1": "SELECT TOOL: Switch to the specified tool",
    "T2": "SELECT TOOL: Switch to the specified tool",
    "T3": "SELECT TOOL: Switch to the specified tool",
    "T4": "SELECT TOOL: Switch to the specified tool",
    "T5": "SELECT TOOL: Switch to the specified tool",
    "T6": "SELECT TOOL: Switch to the specified tool"
  }
}