-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathprinter.cfg
232 lines (206 loc) · 4.18 KB
/
printer.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
#SET_SKEW XY=140.5,140.3,99.4 XZ=140.8,140.9,99.6 YZ=140.5,140.5,99.2
[include mainsail.cfg]
[include macros.cfg]
[printer]
kinematics: cartesian
max_velocity: 500
max_accel: 3000
#max_accel_to_decel: 750
max_z_velocity: 5
square_corner_velocity: 5.0
max_z_accel: 100
[input_shaper]
shaper_freq_x: 29.8507
shaper_freq_y: 34.7222
shaper_type: mzv
[extruder]
step_pin: PB3
dir_pin: !PB4
enable_pin: !PD1
microsteps: 16
#rotation_distance: 7.6190
nozzle_diameter: 0.400
filament_diameter: 1.750
max_extrude_only_distance: 100
heater_pin: PC8
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PA0
#control: pid
#pid_Kp: 21.527
#pid_Ki: 1.063
#pid_Kd: 108.982
min_temp: 0
max_temp: 300
gear_ratio: 42:12
rotation_distance: 26.1891392
pressure_advance: 0.07 #Sunlu White Pla Plus
[tmc2209 extruder]
uart_pin: PC11
tx_pin: PC10
uart_address: 3
run_current: 0.650
#hold_current: 0.500
stealthchop_threshold: 999999
[safe_z_home]
home_xy_position: 195, 120 # Change coordinates to the center of your print bed
speed: 50
z_hop: 10 # Move up 10mm
z_hop_speed: 5
[stepper_x]
step_pin: PB13
dir_pin: !PB12
enable_pin: !PB14
microsteps: 16
rotation_distance: 40
endstop_pin: ^PC0
position_endstop: 0
position_min: 0
position_max: 310
homing_speed: 50
[tmc2209 stepper_x]
uart_pin: PC11
tx_pin: PC10
uart_address: 0
run_current: 0.600
#hold_current: 0.500
stealthchop_threshold: 999999
[stepper_y]
step_pin: PB10
dir_pin: !PB2
enable_pin: !PB11
microsteps: 16
rotation_distance: 40
endstop_pin: ^PC1
position_endstop: 0
position_max: 240
homing_speed: 50
[tmc2209 stepper_y]
uart_pin: PC11
tx_pin: PC10
uart_address: 2
run_current: 0.600
#hold_current: 0.500
stealthchop_threshold: 999999
[stepper_z]
step_pin: PB0
dir_pin: PC5
enable_pin: !PB1
microsteps: 16
rotation_distance: 8
# endstop_pin: ^PC2
# position_endstop: 0.0
endstop_pin: probe:z_virtual_endstop
position_min: -4
position_max: 280
[tmc2209 stepper_z]
uart_pin: PC11
tx_pin: PC10
uart_address: 1
run_current: 0.600
#hold_current: 0.500
stealthchop_threshold: 999999
[heater_bed]
heater_pin: PC9
sensor_type: ATC Semitec 104GT-2
sensor_pin: PC4
#control: pid
#pid_Kp: 54.027
#pid_Ki: 0.770
#pid_Kd: 948.182
min_temp: 0
max_temp: 130
[heater_fan hotend_fan]
pin: PB15
heater: extruder
heater_temp: 50.0
[controller_fan electronic_enclosure_fan]
pin: PC7
idle_timeout: 60
[fan]
pin: PC6
[mcu]
serial: /dev/serial/by-id/usb-Klipper_stm32g0b1xx_09003A000650414235363020-if00
# serial: /dev/ttyAMA0
# restart_method: command
[output_pin beeper]
pin: PB5
[skew_correction]
[save_variables]
filename: ~/klipper_config/sovol/saved_variables.cfg
[bed_screws]
screw1: 42, 35
screw2: 250, 35
screw3: 42, 205
screw4: 250, 205
[screws_tilt_adjust]
screw1:97,205
screw1_name:back_left
screw2:305,35
screw2_name:front_right
screw3:305,205
screw3_name:back_right
screw4:97,35
screw4_name:front_left
screw_thread: CW-M4
[bltouch]
sensor_pin: ^PC14
control_pin: PA1
x_offset: -55
y_offset: 0
#z_offset: 3.499
speed: 10
samples: 2
samples_result: average
probe_with_touch_mode: true
stow_on_each_sample: false
[bed_mesh]
speed: 100
mesh_min: 35, 20
mesh_max: 255, 220
algorithm: bicubic
probe_count: 4
[board_pins]
aliases:
# EXP1 header
EXP1_1=PB5, EXP1_3=PA9, EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>,
EXP1_2=PA15, EXP1_4=<RST>, EXP1_6=PB9, EXP1_8=PD6, EXP1_10=<5V>
#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [heater_bed]
#*# control = pid
#*# pid_kp = 65.045
#*# pid_ki = 1.087
#*# pid_kd = 973.235
#*#
#*# [extruder]
#*# control = pid
#*# pid_kp = 22.976
#*# pid_ki = 1.320
#*# pid_kd = 99.945
#*#
#*# [bltouch]
#*# z_offset = 2.900
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# -0.066250, -0.071250, -0.038750, -0.047500
#*# 0.013750, -0.017500, -0.011250, -0.027500
#*# 0.067500, -0.040000, 0.012500, 0.012500
#*# -0.077500, -0.130000, -0.081250, -0.110000
#*# x_count = 4
#*# y_count = 4
#*# mesh_x_pps = 2
#*# mesh_y_pps = 2
#*# algo = bicubic
#*# tension = 0.2
#*# min_x = 35.0
#*# max_x = 254.99
#*# min_y = 20.0
#*# max_y = 219.97
#*#
#*# [skew_correction sskew]
#*# xy_skew = 0.0014245064677677753
#*# xz_skew = -0.0007099752426328504
#*# yz_skew = -2.220446049250313e-16