3_Rocket.tex

\newpage
\setcounter{page}{1}
\lhead{Rocket}
\lfoot{\thepage / \pageref{end_section_rocket}}
\section*{Rocket}
%\input{0_NoteMissionControl}
\input{0_Legend}

\begin{enumerate}[label=R\arabic*.]

    \item READ THE WHOLE CHECKLIST BEFORE STARTING \checkbox
    
    \starttask{Required tools, materials and personnel}{\hphantom{a}}
    \item \label{rocket_personnel} Personnel
        \begin{enumerate}[label*=\arabic*.]
            \item Propulsion 1: Daniel Frank
            \item Propulsion 2: Luis Büchi
            \item Recovery 1: Georg Mikula
            \item Recovery 2: Michael Pohn
        \end{enumerate}
    \item \label{rocket_tools} Tools
        \begin{enumerate}[label*=\arabic*.]
            \item Faceshields\leftcheckbox
            \item Igniter Tools\leftcheckbox
            \begin{enumerate}[label*=\arabic*.]
                \item Box Cutter\leftcheckbox
                \item White Permanent Marker\leftcheckbox
                \item Thin Stick\leftcheckbox
                \item Scale\leftcheckbox
                \item Safety Glasses\leftcheckbox
                \item Hand Gloves\leftcheckbox
                \item Small Spoon\leftcheckbox
                \item Hot Plate\leftcheckbox
            \end{enumerate}
            \item Airframe Assembly Tools\leftcheckbox
            \begin{enumerate}[label*=\arabic*.]
                \item Hex and Torx for M4 screws \leftcheckbox
            \end{enumerate}
            \item Side Cutters\leftcheckbox
            \item Torx 6, 8, 20\leftcheckbox
            \item Ibus 2.5\leftcheckbox
            \item Masking Tape\leftcheckbox
        \end{enumerate}
    \item \label{rocket_materials} Materials
        \begin{enumerate}[label*=\arabic*.]
            \item Igniter Materials\leftcheckbox
            \begin{enumerate}[label*=\arabic*.]
                \item 6x E-Matches \leftcheckbox
                \item 6x 3D-printed Cartridges \leftcheckbox
                \item 6x Teflon Seal Discs\leftcheckbox
                \item KNO3\leftcheckbox
                \item Sugar\leftcheckbox
                \item Mg\leftcheckbox
            \end{enumerate}
            \item Airframe Materials\leftcheckbox
            \begin{enumerate}[label*=\arabic*.]
                \item 8x black M4 screws (\SI{8}{\milli\meter}) for bodytube \&\newline nosecone coupler \leftcheckbox
                \item 8x black M4 screws(4x\SI{8}{\milli\meter}, 4x\SI{10}{\milli\meter}) for bodytube \&\newline fincan coupler \leftcheckbox
                \item Railbutton, T-nut and M4 screw (\SI{20}{\milli\meter}) \leftcheckbox
                \item 4x M4  screws (\SI{10}{\milli\meter}) \leftcheckbox
            \end{enumerate}
            \item Main Battery, Backup Battery\leftcheckbox
            \item Assortment of zip ties\leftcheckbox
            \item Clampband\leftcheckbox
            \item Reserve Shock Absorber\leftcheckbox
            \item Payload\leftcheckbox
            \item SD cards for cameras\leftcheckbox
            \item Loctite\leftcheckbox
            \item 5.5 Wrench\leftcheckbox
            \item Altimax Cover\leftcheckbox
            \item Felt tip pen (can be permanent marker)\leftcheckbox
        \end{enumerate}
    
    \starttask{Recovery Assembly}{\hphantom{a}}
    \begin{figure}[H]
        \centering
        \includegraphics[width=0.7\linewidth]{recovery.png}
        \caption{Recovery line setup}
        \label{fig:chutes}
    \end{figure}
    \item Using loctite, screw upper clampband screws into upper clampband coupler without threads sticking out \checkbox
    \item Push rubber bands onto screws and fix in place with cable ties \checkbox
    \item Mount clampband line to lower coupler \checkbox
    \item Mount shockbar to Recovery main tube\checkbox
    \item Slide main shock cord onto shockbar\checkbox
    \item Slide main deployment line onto shockbar (twice)\checkbox
    \item Thread main deployment line through both main\newline deployment linecutters\checkbox
    \item Mount lower clampband coupler to main tube \checkbox
    \item Slide both drogue deployment linecutter through main tube\checkbox
    \item Mount RCU to RCU cover\checkbox
    \item Mount RCU to main tube (cables connected)\checkbox
    \item Tape antenna to main tube\checkbox
    \item Ensure shock absorber is intact. No more than the first stitched fold shall be loose.\checkbox
    \item Fold main shock cord\checkbox
    \item Thread deployment bag onto deployment bag line\checkbox
    \item Fold main chute like in this video:\newline www.youtube.com/watch?v=g$\_$v6V4a9-PA\checkbox
    \item Insert main chute into deployment bag\checkbox
    \item Connect main shock cord to main chute (blue-brown)\checkbox
    \item Secure shackle with masking tape \checkbox
    \item Insert main shock cords into deployment bag\checkbox
    \item Close deployment bag\checkbox
    \item Insert deployment bag into main tube\checkbox
    \item Thread deployment bag holdback line through main tube\checkbox
    \item Connect line 2, drogue line and deployment bag line according to\newline figure \ref{fig:chutes} \checkbox
    \item Connect line 2 and deployment bag line to drogue line (green) \checkbox
    \item Secure shackle with masking tape \checkbox
    \item Connect nosecone line to drogue chute (black) \checkbox
    \item Wrap drogue shock lines around drogue chute, add two additional turns of the drogue line\checkbox
    \item Fold remaining drogue line and nose cone line individualy in a figure eight pattern \checkbox
    \item Lay drogue chute and folded lines on top off main chute\checkbox
    \item Place drogue tube on top off main tube and make sure TRS charging connector is connected\checkbox
    \item Temporarily tape together with masking tape (mark tape as RBF)\checkbox
    \item Connect clampband to clampband line \checkbox
    \item Mount payload bay to recovery section \checkbox
    \item Connect RCU to PMU (CAN/Power) \checkbox
    \item Mount main battery with zip ties \checkbox
    \item Mount backup battery with zip ties \checkbox
    \item Insert temporary RBF pin into PMU\checkbox
    \item Mount PMU \checkbox
    \item Connect cameras to PMU \checkbox
    \item Connect payload cable to PMU \checkbox
    \item Zip tie cables \checkbox

    \starttask{Non-energetic Rocket Assembly}{\hphantom{a}}
    \item \label{rocket_non_energetic_start} Check if cable management is done properly and fix if necessary\checkbox
    \item Make photos of internals for Launch Readiness Review\checkbox
    \item Mount airframe-fincan coupler to propulsion system (4 M4x10 screws)\checkbox
    \item Rotate propulsion system until connectors are on top \checkbox
    \item Ensure upper rail button T-nut is mounted to propulsion system \checkbox
    \item Slot propulsion system into body tube \checkbox
    \item Verify alignment of ox pressurant fill and vent to the respective openings in the body tube \checkbox
    \item Screw body tube to thrust structure (4 M4x10 screws)\checkbox
    \item Screw body tube to airframe-fincan coupler (4 M4x8 screws) \checkbox
    \item Rotate fuel tank assembly to correct orientation (threaded inserts aligned with holes in body tube) \checkbox
    \item Screw fuel tank assembly in place (8 M4x8 screws) \checkbox
    \item Mount upper rail button to T-nut using threadlocker\checkbox
    \item Align fuel pressurant fill with opening in body tube \checkbox
    \item Verify temporary RBF is inserted\checkbox
    \item Connect linecutters to Altimax \checkbox
    \item Verify batteries connected properly \checkbox
    \item Verify Altimax connected properly \checkbox
    \item Verify RCU connected properly \checkbox
    \item Verify SD-cards in cameras \checkbox
    \item Verify payload inserted and connected properly \checkbox
    \item Verify if clampband screws are tight \checkbox
    \item Remove runcam covers \checkbox
    \item Connect propulsion cables to recovery section \checkbox
    \item Connect umbilical cables to recovery section \checkbox
    \item Slot recovery system into body tube and fix with 8 screws\checkbox
    \item Verify that the cameras and RBF pin align with the holes\newline in the airframe.\checkbox
    \item Cover rocket with opaque cover\checkbox
    \item Swap temporary RBF pin with final RBF pin\checkbox
    \item \label{rocket_non_energetic_end} Report non-energetic rocket assembly completed to Mission Lead.\checkbox
    
    \starttask{Energetic Rocket Assembly}{\hphantom{a}}
    \item \label{rocket_energetic_start} Prepare tools for assembly \checkbox
    \begin{enumerate}
        \item Ibus size 2.5 \checkbox
        \item Torx size 6 \checkbox
        \item Torx size 8 \checkbox
        \item Torx size 20 \checkbox
        \item Face shields \checkbox
    \end{enumerate}
    \item Remove nosecone from upper clampband\checkbox
    \item Put upper clampband onto lower clampband (ensure clampband line is not pinched) \checkbox
    \item Prepare drogue deployment line \checkbox  
    \item Thread drogue deployment line through drogue deployment linecutter \checkbox
    \item Open clampband tensioner \checkbox
    \item Thread drogue deployment line through both clampband halves and knot together (as tight as possible)\checkbox
    \item Thread clampband line inbetween the couplers \checkbox
    \item Put on face shields \checkbox
    \item Temporarely affix clampband to coupler with zip tie \checkbox
    \item Connect clampband halves with tensioner (T6) \checkbox
    \item Ensure clampband halves are connectet securely \checkbox
    \item Remove zip tie \checkbox
    \item Tighten clampband (H2.5) \checkbox
    \item \label{rocket_energetic_end} Mount RBF zip tie around clampband \checkbox
    
    \item Report energetic rocket assembly complete to Mission Lead.\checkbox
    
    \starttask{Final Rocket Assembly}{\hphantom{a}}
    \item \label{rocket_final_start} Connect TRS battery to charger \checkbox
    \item Connect TRS battery to TRS \checkbox
    \item Secure TRS battery to TRS with masking tape \checkbox
    \item Install TRS in TRS tube (T20) \checkbox
    \item Tension slingshot \checkbox
    \item Mount slingshot retainer (T8) \checkbox
    \item Remove RBF tape \checkbox
    \item Mount nosecone onto upper clampband \checkbox
    \item Secure nosecone (8 screws, H2.5) \checkbox
    \item Install RBF zip tie on clampband \checkbox
    \item Connect nosecone (including upper clampband coupler) to nosecone line (red-black)\checkbox
    
    \starttask{Igniter Installation}{\hphantom{a}}
    \item Securely screw in Igniters.\checkbox
    \item Connect igniters to igniter cables.\checkbox
    \item Properly cable manage igniter cables.\checkbox
    
    \item \label{rocket_final_end} Report Rocket Final Assembly comlete to Mission Lead\checkbox

\label{end_section_rocket}
\end{enumerate}